Solar Panel Single Axis Auto Solar Tracker Sun Complete System Wind Speed Sensor. New Solar Tracker Dual Axis Controller Solar Automatic Tracking System. Two-degree-of-freedom Platform Tracking Sun Tracker.
(Both the Detector Head & Wind Speed Sensor have been updated). Standby current: less than 0.02A. Maximum control current: less than 6A.
Tracking accuracy: highest 1 degree. Wind speed start-up protection function.Anti-power reverse connection protection function. Remote control distance:10 price.
Power input (12-24V DC, left Positive right negative). East-west axis motor output 10. North-south axis motor output 11.
When the backlight of LCD display is not operated, it can be controlled to extinguish to save power. The contrast of LCD screen should not be disturbed, so as to avoid the misadjustment of the contrast to the lowest level, which is supposed to be a display failure. TXValues can generally be set to120More than a second, because the sun moves slowly, about four minutes before moving once. TYThe value can be set to about 100 seconds according to the situation. T3/4/5/6According to the moving speed of the platform, conceive what attitude the platform should move to resist the wind in the case of wind, and then set the corresponding time parameters.Generally, it is to perform leveling, that is, to drive northward to the end. T7It is the time delay of self-locking after leveling in the wind. The time value can be set a little longer to avoid frequent action of intermittent wind-driven devices. 600 About seconds is appropriate. T8It is the delay time of weak sunshine, which is used to calculate the duration of weak sunshine. This value should be set a little longer to avoid frequent platform movements caused by short rains and clouds.
1200More than seconds is appropriate. T9/10/11/12 is the time for executing the specified action when the sun is weak. According to the moving speed of the platform, the author conceives how to move to a suitable position and suggests that the east-west axis should be in the middle of the North-South axis. That will doThat is to say, to go east for a certain time to determine that the time can end, and then to go west for half the time of the whole journey. The north-south proposal is to leveling because the night is longer, leveling is conducive to shelter from the wind, and if it is daytime, in case the sun is temporarily lost, leveling is also conducive to the capture of the sun when it appears again.V1Tracking accuracy settings, generally in0.00-0.15Set up between. According to the accuracy and tracking effect of the platform, 0.01 is recommended. V2It is the wind speed start-up voltage. The default configuration of the wind speed sensor is as follows 0.1VSettings can be adjusted by users themselves. If other wind speed sensors are used, voltage type wind speed sensors must be used.
The parameters should be set by themselves according to their specifications. The method of fuzzy setting is to observe how much F = is when you feel that the wind in the environment at that time may damage the platform. On this basis, you can set it a little lower. For example, if F = 0.30V at that time, it would be reasonable to set the threshold V2 to 0.25.
V3Is the weak threshold of sunlight, recommended by1.5V-1.8V is reasonableSet up. X0/Y0The settings depend on the error of the detection head.
If there is no specific precision required, the settings can be set to1.0Yes. Azimuth detection headM6Bolts are fixed.
You need to open one on the north side of the platform. M6.1A hole for fixing the detection head. The installation hole size of the main control box is four.
M6Holes, left and right spacing18.2CMUpper and lower spacing5.1CM. The installation hole size of the wind speed sensor is: two spacing5.6CMOfM6Hole. External limit method is strongly recommended.
If the limit signal is used to introduce the controller, four switches with constant open contacts are needed to be arranged at the limit location. When the switch is closed, the T4:When performing a specified action of exceeding the wind speed limitUndertakeT3After time, the time value of driving device to the West. T5:When performing a specified action of exceeding the wind speed limitThe time value of the device driving northward.T6:When performing a specified action of exceeding the wind speed limitUndertakeT5After time, the time value of the driving device heading south. T7After the specified action of wind speed exceeding the limit, the self-locking time of the controller is designed to prevent the effect of wind speed from being intermittent and causing frequent action of the device. /Tracking, in the self-locking time, if the wind speed re-exceeds the value, then the time immediately re-timed, so that the device will not operate frequently. T8: Delay value of weak duration of sunlight.
T9:Time value of the device driving eastward when performing specified action with weak sunlight. T10:implementWeak sunlightDesignated action timeUndertakeT9After time, the time value of driving device to the West. T11:implementWeak sunlightDesignated action timeThe time value of the device driving northward. T12:implementWeak sunlightDesignated action timeUndertakeT11After time, the time value of the driving device heading south. T13: The set value of the duration delay time of the recovery of sunlight after the occurrence of the weak state of sunlight.
T14: When the reversal function of the Northern Hemisphere is activated, the device performs specified actions and drives eastward. T15: When the reversal function of the Northern Hemisphere is activated, the device performs the specified action and drives the time value westward after taking the T14 time. V1Tracking Accuracy Settings, which set the Tracking Accuracy Interval Voltage Value, that is, East/West and South/How much is the difference between the voltage values of silicon wafers detected in North ChinaVWhen the controller considers it necessary to move the device or aim at the sun, the smaller the value, the higher the accuracy, and vice versa, the lower the accuracy, which needs to be set according to the characteristics of the platform. V2When the output voltage of the wind speed sensor is higher than the threshold value set by the controller, the controller considers that it is necessary to regulate the action immediately to protect the platform.
V3When the voltage value of silicon wafer in the first four directions of detection is no higher than this value, the controller considers that the current sunshine is weak, there is no power generation value, cancels tracking and delays. T8If the sunshine hasn't been restored after the time, perform the prescribed action.
X0 Because the performance of the silicon wafers in the four directions of the detection head can not be completely consistent, increasing the correction base makes the controller correct the difference of the components of the detection head, and the device can more accurately align with the sun. The method of setting the parameters is explained in detail later. Y0The principle of on-line correction of north-south axis angle is the same as that of north-south axis angle. SUMMER: The Northern Hemisphere Sun Reversal function is activated. How to enter the setting state: Press and hold the remote control in any state The bond lasts more than four seconds.
This page shows the real-time voltage values of the silicon wafers in the first four directions. In debugging and other situations, the output voltage signals of the azimuth detection head can be viewed in real time on this page.
Here/PressThe key can turn the page. /Key to add or subtract parameter settings. /Keyboard press once is a single value addition and subtraction, hold still, is fast addition and subtraction.
Press/The key can be looped in the above parameter setting state, press/Key can add or subtract parameters, after setting, pressQUITAfter the key, save the exit. X0/Y0The method of setting parameters is as follows. On a sunny day (try not to be sunny in the morning or evening or at noon at the most time, in the morning or afternoon is more appropriate), first enter the manual operation state, with the remote control manual control platform aiming at the sun, confirm the platform. Align completely with the sunThen press down.
SETKeyboard more than 5 seconds, that is, enter the setting surface, enter the first and second pages after setting, appear the value of East-West and North-South voltage of the detection head, and show the corresponding reference of correction cardinality below, remember the corresponding value of X0 and Y0, and then turn pages into the setting pages of X0 and Y0 with remote control, modify the corresponding parameters to the corresponding value, save and exit. All of the above states are shown on LCD screen, including all kinds of time and states, which are displayed in numbers or letters. The item "Solar Panel Single Axis Auto Solar Tracker Sun Complete System Wind Speed Sensor" is in sale since Monday, June 14, 2021. This item is in the category "Home & Garden\Home Improvement\Electrical Supplies\Alternative Energy Supplies\Solar Power Supplies\Solar Power Accessories".The seller is "gaweeshhimajale0" and is located in beijing. This item can be shipped worldwide.